More Culture

-
On Sunday we visited Kings Dominion, and there was a LOT of rollercoaster action.
Best one there is the Intimidator 305 (that being the height in feet), it's a mile long and reaches 94 mph.  After the illness of Six Flags I was taking it easy and missing quite a few rides, but I went on this a couple of times.  Dominator was good too, if I was a nerd I'd mention it's the same model of B&M coaster as AT's Oblivion, though much longer and minus the freefall drop.
Again, rollercoaster-enthusiast weirdos would tell you that Anaconda is a late model Arrow Dynamics Corkscrew.  It's quite long but with a painful full-stop part way through, feels like it was too intense and had to be tamed.  Pretty rough ride.
There's some good wooden coasters too, such as Rebel Yell which is 2 racing coasters, like the Grand National at Blackpool (really painfully rough).  I didn't do the others, apparently they're even tougher on the arse so I sat them out and had a pink milkshake with cream on top instead :)
Look, a car!  Intimidator is NASCAR themed.
Being halloween, in the evening the zombies came out.  This was excellent, best sound/lighting/themeing I've seen.  We went through a maze full of monsters in medical uniforms, carrying out experiments on humans.  It was AWESOME, like everybody, everybody, here says.  About everything.

Popular posts from this blog

Adding bluetooth to a Mini with Harman Kardon audio

-
Image
My R53 Cooper S has the unexpected bonus of the Harman Kardon premium audio system.  While it has impressive power and sound quality (once you discover the hidden settings ), it's firmly stuck in the past with just CD and analogue radio.  You can't change the head unit as the speakers are all wired to the 10-channel amp that lives in the boot, so new cables would need to be run from the head unit to each speaker, which would be an almighty faff. I wanted to add bluetooth so I could play my cheesy '80s music from Spotify, so bought a Grom BT3  which is a small module that plugs into the CD-changer port on the rear of the standard-fit Boost head unit.  It allows you to stream music from your mobile, and make/receive calls via the supplied microphone.  You can also buy another module that plugs into the Grom to provide DAB radio, USB, or iPod wired connections, I didn't bother with any of those, I just wanted Bananarama, loud. There are 2 versions of the Grom for BMW
Read more

BMW E39 diesel pump replacement

-
Image
I replaced the fuel pump in the tank of the 530D yesterday.  It was quite fiddly and I couldn't find any useful guide on the internet, so I thought I'd create a quick outline of the procedure: Symptoms of failure : poor starting/cutting out when the fuel level falls to around a quarter of a tank. Cost : £42 from GSF , plus 2x 9mm petrol hose clips (the originals are not reusable). Procedure :  remove the rear seat base by pulling up sharply on it's front edge (there are a pair of spring clips holding it in place).  Beneath are 2 access panels to the tank, the pump is under the right-hand side one (behind the driver on a UK right-hand drive car).  Remove the cover and disconnect the 2 hose connections and the electrical plug (removed by pushing the locking clip sideways).  Unscrew the locking ring by gently rotating it with a hammer and chisel. Now slowly remove the fuel sender unit, noting it's orientation and how it slots into the pump assembly below - it'
Read more

MINI tailgate hinge replacement

-
Image
I replaced the snapped tailgate hinge on t'old MINI today, and it wasn't too bad a job.  The design is a bit crap and they tend to seize, and then break and attempt to bonk you on the head with the tailgate.  Didn't like that. The hinge is held on by a single nut but you need to partially drop the headlining to reach it.  To do this you need to: remove the tailgate seal remove the rear seats remove the rear side panel trim on the affected side This is all covered by some helpful folks in this YouTube video.  After this, you need to remove the white C-pillar trim; it's held in by 4 plastic tabs (2 top, 2 bottom), which fit into metal clips in the body.  It needs a sharp tug but there is a fair risk of breaking the tabs, but I got away with it. Now you should be able to gently pull down the headlining, to release the clip in the centre: That should give just enough clearance to get a 13mm socket onto the nut securing the hinge.  There is quite a lot
Read more